How can I install and configure my FRITZ!Box Fon WLAN 7113?

• en
• »
• Support
• »
• Installation & usage
• »
• Internet
• »
• How can I install and configure my FRITZ!Box Fon WLAN 7113?

Basic and Internet configuration

The basic configuration wizard only appears when you connect the Fritz!Box for the very first time or after a reset to factory defaults.

Step 1 - Opening the web interface

Open your web browser (Internet Explorer, Firefox,…) and go to: http://fritz.box. 

Step 2 - Language choice

Now you see the wizard for the first basic configuration; the standard language is German. 
Select English or another language if preferred. 
Click on Weiter (Next) to continue. 

Step 3 - Regional settings

The language of the web interface has now changed to the language of your choice; in our case to English. 
Next you see the screen to choose the regional settings. 
In the combo box you select Belgium and click on Apply. 

Step 4 - Reboot

The Fritz!Box will now automatically reboot and after about 1 minute you can click on To Overview to go to the main page of the web interface. 

Step 5 - Set the Administrator password

First you are asked to assign a password. 
Assigning a password will protect your settings and avoid unwanted access to your Fritz!Box. 
In case you would like to do this later, you can uncheck the option and click on Log On to go to the main page of the web interface. 

Step 6 - Welcome screen

The next screen is the Welcome screen, where you can start the wizard to set up your internet connection. 
This wizard is not needed to set up your edpnet connection. 
Therefore you click at the top on Settings so that you can configure the settings manually. 

Step 7 - Leaving the wizard

You will see a screen asking you to confirm to leave the wizard; click on OK. 

Step 8 - Wizards

This screen will show you all the available wizards. 
In the menu on the left you click on Advanced Settings. 

Step 9 - Advanced Settings

Here you will see all the Advanced Settings. 
Click on Internet. 

Step 10 - Online Monitor

Now you arrive in the screen Online Monitor where you can see the status of the internet connection. 
(If there is a DSL signal on the line, the light will turn green.) 
In the menu on the left you click on Account Information. 

Step 11 - Operation Mode

This screen is divided in Operating Mode and Connection Settings. 
Under Operating Mode you choose for Use one Internet connection for all computers (router). 

Step 12 - More settings

After this there will automatically appear more settings. 

Step 13 - Account Information

Under Account Information you select Account information required (PPPoE/PPPoA connection). 
After this there will automatically appear more settings. 

Step 14 - Connection Settings

Under Connection Settings you fill in the following values: 
User name: your username (for example: username@EDPNET) 
Password: your password (for example: 1234) 
Password confirmation: confirm your password. 

Choose Maintain Internet connection permanently to prevent your connection from being automatically closed. 

Under DSL ATM Settings you choose for Define ATM settings manually and you fill in the following values: 
VPI: 8 
VCI: 35 
Under Encapsulation you choose PPPoE. 

In the following picture, the correct settings are shown for edpnet in Belgium. 
Now click on Apply. 

Now you will receive a notification that says you chose to maintain your connection permanently. 
Click on OK. 

Your internet connection is now set up and ready to use. 
(If everything is correctly configured; Internet will turn green on the Overview screen.)

VoIP configuration

Via these steps you can configure your edpnet telephony.

Step 1 - Overview

At the bottom of the main screen Overview click on Internet telephony to set up your VoIP number(s). 

Step 2 - Internet Telephony

In the first tab Internet Numbers you can add a new VoIP number. 
To add a new number you click on New Internet Number at the right bottom. 

Step 3 - Internet Telephone Number

In the next screen you can fill in the complete configuration for your VoIP telephone number: 

Internet number: my phone number (for example: 032656700) 
User name: my phone number (for example: 032656700) 
Password: my password (for example: 1234) 
Password confirmation: confirm your password. 
Registrar: voip.edpnet.be 

The 2 following options under registrar are automatically selected. 

Click on OK to save the settings. 

Step 4 - Overview Internet Telephony

Now you end up again in the main screen for Internet Telephony. 

Step 5 - Advanced Settings

Click in the tab Advanced Settings and disable the option Use fixed-line substitute connection. 
Click on Apply. 

 
Your Internet telephony is now configured and ready to use. 
(If everything is correctly configured; Telephony will turn green on the Overview screen.)

Enabling Expert Mode

You will need the Expert Mode in order to modify the advanced settings of your FRITZ!Box Fon WLAN 7113. 

Go to Advanced Settings / System / Expert Mode. 
You will see the Expert Mode page. 
Tick the option Show expert settings and click the Apply button to enable the Expert Mode. 

The Expert Mode is enabled!

Enabling Remote Administration

Please follow the steps described below in order to enable the remote access to your FRITZ!Box Fon WLAN 7113. 

First please make sure you are in the Expert Mode.

Then go to Advanced Settings/ Internet / Permit Access / Remote Access. 
Tick the option called Enable remote access and fill in the necessary information:

• User: type the username that will be used for the remote access.
• Password: type the password that will be used for the remote access.
• Password confirmation: confirm the password.

Then click the Apply button to save the changes. 

The Remote Administration is enabled!